视频资料

视频资料

视频资料

视频资料

1986年日立精机数控车床488小时 - 经络机械公司262-854-5054

这是我们的1986日立精机Hitec等20数控车床8“夹头,尾座,FANUC 10TF充分CONV ersational CNC控制系统和488个切割小时的短视频,本机是目前可供出售的,在我们的仓库进行检查下电源设施。如果您有关于本机视频不回答任何问题,您可以致电262-854-5054或sales@meridianamachinery.com我们下面列出了本机的全部规格,谢谢。日立精机国际展贸中心“ X轴20数控车削中心一般规格:最大SWING17.7“ 最大切割LENGTH12 MANUFACTURE1986日期TRAVEL6.7“ Z轴TRAVEL13.4“ 快速进给率X AXIS400 IPM的快速进给率X AXIS480病虫害综合防治主轴SPEEDS20 - 3600 RPM的主轴MOTOR15 / 10 HP 主轴NOSEA2 - 6 主轴BORE2.0“ 炮塔CAPACITY12站尾座TAPERMT#4 尾座套筒TRAVEL3.91“ 尾座套筒DIAMETER3.15“ APPROX。DIMENSIONS98“× 61”× 70“的机器重量(约)7000磅配备:一般数值/ FANUC 10TF数控控制会话&G代码编程,14“彩色显像管及RS - 232C端口接口8“3爪通孔液压液压尾座/可编程套筒夹头工具眼睛/刀具预调仪,负载和速度表全密闭式安全保护所有可用的炮塔模具手册*** TECH校机-像新的一样条件*** *****这是不PAINTED -所有原始***** *****总计切割时间:488(见照片)***** 串行数21827 - SC 的位置:我们根据权力的仓库

This is a short video of our 1986 Hitachi Seiki Hitec 20 CNC lathe with 8" chuck, tailstock, Fanuc 10TF full conv ersational CNC control and 488 total cutting hours. This machine is currently available for sale and is under power for inspection in our warehouse facility. Should you have any questions about this machine that are not answered by the video, you may contact us at 262-854-5054 or sales@meridianamachinery.com. Full specifications of this machine are listed below. Thank you.

HITACHI SEIKI HITEC 20 CNC TURNING CENTER

GENERAL SPECIFICATIONS:

DATE OF MANUFACTURE1986
MAXIMUM SWING17.7"
MAXIMUM CUTTING LENGTH12"
X AXIS TRAVEL6.7"
Z AXIS TRAVEL13.4"
RAPID TRAVERSE RATE X AXIS400 IPM
RAPID TRAVERSE RATE X AXIS480 IPM
SPINDLE SPEEDS20 - 3600 RPM
SPINDLE MOTOR15/10 HP
SPINDLE NOSEA2-6
SPINDLE BORE2.0"
TURRET CAPACITY12 STATIONS
TAILSTOCK TAPERMT #4
TAILSTOCK QUILL TRAVEL3.91"
TAILSTOCK QUILL DIAMETER3.15"
APPROX. DIMENSIONS98" x 61" x 70"
MACHINE WEIGHT (APPROX)7000 LBS

 


EQUIPPED WITH:

GENERAL NUMERIC/FANUC 10TF CNC CONTROL
FULL CONVERSATIONAL & G-CODE PROGRAMMING
14" COLOR CRT & RS-232C PORT INTERFACE
8" 3-JAW HYDRAULIC THROUGH HOLE CHUCK
TOOL EYE/TOOL PRESETTER, LOAD & SPEED METERS
HYDRAULIC TAILSTOCK W/PROGRAMMABLE QUILL
FULLY ENCLOSED SPLASH & SAFETY GUARDING
ALL AVAILABLE TURRET TOOLING & MANUALS
***TECH SCHOOL MACHINE - LIKE NEW CONDITION***
*****THESE ARE NOT PAINTED - ALL ORIGINAL*****
*****TOTAL CUTTING HOURS: 488 (SEE PHOTO)*****
SERIAL NUMBER 21827-SC

LOCATION: ON OUR WAREHOUSE FLOOR UNDER POWER

 0.36521291732788 s